Bore evacuator
Animated sequence of how a bore evacuator works.
A bore evacuator.
A bore evacuator or fume extractor is a device which removes lingering gases and airborne residues from the barrel of an armored fighting vehicle's gun after firing, particularly in tanks and self-propelled guns. By creating a pressure differential in the barrel after the shell leaves, the bore evacuator causes most of the propellant gases and combustion residues to exit via the muzzle. Thus, when the breech opens for reloading, those gases and residues do not escape into the crew compartment and pose a hazard to the gun crew.[1]
Description
Foreground, a close-up of the bore evacuator on an M1A1 Abrams, while another tank fires in the background
The evacuator is a passive device generally consisting of a ring of holes drilled into the barrel, surrounded by a cylindrical pressure reservoir that is sealed to the barrel's surface. As the shell moves down the barrel during firing, it creates a high pressure in front of the projectile and the evacuator is filled with high pressure air through the holes. As the shell passes farther, the pressure behind it begins to drop, and suddenly returns nearly to atmospheric pressure as the shell leaves the barrel. During this process the high-pressure air in the reservoir begins to blow back into the barrel towards the front of the gun tube. By aiming these holes forward, their exhaust causes the pressurized air to be blown forward and out of the barrel, extracting fumes from the barrel.[2]
Various designs attempt to improve on the basic concept in any number of ways. One common change is to use two sets of holes, each designed specifically to be efficient at capturing or releasing the gas. In this case the forward set of holes is similar to the single-hole example, but a second rearward set of holes is added, using check valves (typically ball bearings in a pit) to allow the high-pressure gases in, but not out again. The system may be arranged to allow the gases to escape through the forward set of holes before the shell reaches it, causing a partial vacuum to develop directly behind the shell, aiding extraction.[2]
For best results, the breech must be opened at the proper time, just as the forward momentum of the gases reaches its maximum, the peak flow. This means that bore extractors are normally used only on guns with semi-automatic or fully automatic actions, where the breech is opened and the shell ejected as part of the recoil process.
The T-14 Armata needs no bore evacuator
Evacuators reduce the chances of explosive propellant gases flowing backwards into the turret, causing combustion as they mingle with oxygen, though this can still happen if the evacuator is poorly designed, poorly maintained, or damaged. Unprotected bore evacuators damaged by bullets have caused considerable problems in past conflicts, but up-armouring solved this problem.
Bore evacuators are a common feature of most modern tanks. The Russian T-14 Armata is a counterexample, lacking a bore evacuator because its turret is uncrewed.
References
^ Perrett, Bryan (1987). Soviet Armour Since 1945. London: Blandford Press. ISBN 0-7137-1735-1..mw-parser-output cite.citation{font-style:inherit}.mw-parser-output .citation q{quotes:"""""""'""'"}.mw-parser-output .citation .cs1-lock-free a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/6/65/Lock-green.svg/9px-Lock-green.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .citation .cs1-lock-limited a,.mw-parser-output .citation .cs1-lock-registration a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/d/d6/Lock-gray-alt-2.svg/9px-Lock-gray-alt-2.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .citation .cs1-lock-subscription a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/a/aa/Lock-red-alt-2.svg/9px-Lock-red-alt-2.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registration{color:#555}.mw-parser-output .cs1-subscription span,.mw-parser-output .cs1-registration span{border-bottom:1px dotted;cursor:help}.mw-parser-output .cs1-ws-icon a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/4/4c/Wikisource-logo.svg/12px-Wikisource-logo.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output code.cs1-code{color:inherit;background:inherit;border:inherit;padding:inherit}.mw-parser-output .cs1-hidden-error{display:none;font-size:100%}.mw-parser-output .cs1-visible-error{font-size:100%}.mw-parser-output .cs1-maint{display:none;color:#33aa33;margin-left:0.3em}.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registration,.mw-parser-output .cs1-format{font-size:95%}.mw-parser-output .cs1-kern-left,.mw-parser-output .cs1-kern-wl-left{padding-left:0.2em}.mw-parser-output .cs1-kern-right,.mw-parser-output .cs1-kern-wl-right{padding-right:0.2em}
[page needed]
^ ab "Engineering Design Handbook; Guns Series, Muzzle Devices", AD838748, US Army
Further reading
 | Wikimedia Commons has media related to Bore evacuators. |
Woodley, C.R. (May 2001), "Modelling of Fume Extractors" (PDF), 19th International Symposium of Ballistics, Interlaken, pp. 273–280, retrieved 2014-01-07
Pei, Qing-Xiang; Foo, Richard (May 2001), "Modeling and Simulation of the Gas Charging and Discharging Processes on Gun Bore Evacuator" (PDF), 19th International Symposium of Ballistics, Interlaken, pp. 281–288, retrieved 2014-01-07
